You are here: Home » News » Technology Insight » How to Choose a Lenticular Filter Housing: 7 Specs You Can't Overlook

How to Choose a Lenticular Filter Housing: 7 Specs You Can't Overlook

Views: 39     Author: Site Editor     Publish Time: 2026-11-12      Origin: Site

Inquire

facebook sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Choose a lenticular filter housing by specifying the assembly it must hold and the service it must perform. A vessel's nominal diameter is only part of that specification. The mounting arrangement, contact materials, instruments and equipment scope determine whether the offered configuration can be installed and evaluated as intended.

Our industrial buyer's selection guide connects the liquid and media requirement to the system size. The seven specifications below turn that process requirement into a drawing, an equipment order and a practical acceptance plan. State them before asking suppliers to compare prices.

1. Module connection and sealing interface

Identify the exact module code and connection format. Request the dimensions and drawing needed to assess seating, sealing faces and the route to the filtrate outlet. Include any adapters in the review.

The existing vessel drawing is especially useful for a replacement inquiry. Photographs can support identification, but the quotation should resolve the mechanical details through controlled part information. Have the supplier record any assumption that still requires confirmation.

Pall's module instructions distinguish installation arrangements for different connection styles. The purchasing implication is to obtain the instructions and drawing for the proposed combination, including any alternative manufacturer's parts. It is not evidence that all connections within a nominal size are interchangeable.

2. Approved module load and effective area

Specify diameter, module height, cell arrangement and number of modules together. Ask for the effective area of the exact parts being supplied. Establish the area requirement from representative feed, required transfer time and the accepted volume demonstrated in a trial.

If the site handles variable lots, request a drawing for every intended loading arrangement. A smaller load may need different mounting parts or a different center post. Confirm how the stack will be supported and sealed.

Include the smallest planned lot in the assessment. Product retained during startup and draining can affect the value of a configuration chosen only for the largest batch.

Mechanical detail

Confirmation needed

Module identity

Code, grade, dimensions and connection

Loading

Quantity, stack height and approved arrangement

Effective area

Listed area of each supplied module and total assembly

Internal hardware

Posts, adapters, compression parts and supports

Reduced load

Separate drawing and required parts where permitted

Service envelope

Clearance for dome and module removal

Keep those details with the equipment order. They support both initial assembly and the next replacement-module purchase.

02-approved-module-assembly-1600x1000.png

3. Product-contact materials

Identify metal grade and the materials used for seals, internals and connected contact parts. Provide the liquid composition, temperature and expected exposure. Add the preparation and cleaning fluids to the same review.

Request evidence appropriate to the intended application. A material name does not establish that the complete configuration is suitable for every chemical or process condition. Where the site has regulated documentation requirements, define them in the inquiry.

Keep component identity traceable to the supplied configuration. Ask how changes to contact materials will be communicated so the site can assess later replacements against its approved record.

4. Operating and cleaning conditions

State filtration pressure and temperature requirements separately from the cleaning cycle. Request the limits of the complete assembly and identify which component governs each applicable constraint.

Distinguish the vessel's service rating from the module's differential-pressure limit. The two values answer different equipment questions. Operators need the documented limits and a procedure that describes the approved operating arrangement.

Disclose carbonation, solvent use and any gas-assisted recovery or storage. Obtain written confirmation for the intended service, including connected equipment. A liquid-housing description leaves those additional requirements unresolved.

5. Instrumentation and process connections

Specify the inlet and outlet connections to match the actual line. Identify pressure-measurement locations on both sides of the filtration assembly. Confirm how process flow will be established and checked.

Give the supplier information about the existing pump and controls if they will be retained. Review the proposed duty against the assembly's permitted conditions. Where the pump is included in the offer, request its duty and control basis.

Include venting, drainage and sampling connections needed for the approved procedure. Consider whether operators can read instruments and obtain samples in the installed position, with the equipment and piping arranged as proposed.

6. Access, handling and maintenance

Check the footprint and the space required during servicing. Operators need clearance to open the vessel and remove wet modules. Obtain relevant weights and the handling arrangement for the dome and other removable parts.

Consider drainage and maintenance in the layout review. A location that fits the closed vessel may create additional work during removal or cleaning. For mobile equipment, review the trolley's operating position and access to connections.

Ask which seals and service parts should be stocked and how they are identified. Keep the assembly instructions and replacement list available to the people performing changeovers.

03-operating-conditions-and-service-1600x1000.png

7. Complete supply scope and acceptance documents

Use our lenticular filter system setup checklist to identify the vessel, modules, mounting hardware, valves and instruments included in the purchase. Mark the pump, hoses, controls and other items the site will supply.

Request the final drawing and bill of materials before shipment. Define the documents needed to assess the specified materials, equipment tests and operating conditions. Confirm commissioning responsibilities and the acceptance run.

Order item

Acceptance record

Housing and mounting parts

Drawing and itemized equipment identification

Initial modules

Correct codes, quantity, grade and area

Contact materials

Required component and material documents

Instruments and fittings

Supplied list and approved locations

Preparation and operation

Applicable instructions and completion criteria

Production duty

Outlet tests, operating endpoint and accepted-volume record

Commercial scope

Delivery basis, exclusions and agreed support

Apply the same scope to each quotation. A vessel-only offer and a system with operating accessories need different allowances for installation and startup.

04-supply-scope-and-acceptance-1600x1000.png

Use the specifications to compare proposals

Review unresolved items before selecting the lowest total. A missing interface drawing, unspecified seal or excluded instrument can affect the work required to bring the system into service.

LOONGFiltration's lenticular housing page identifies a configuration inquiry starting point. Send the seven-part specification with your liquid description and any existing module drawings. Request the proposed equipment by code and ask the supplier to state its assumptions.

Frequently asked questions

Should I decide between twelve- and sixteen-inch modules first?

Start with the area and operating duty, then compare approved loading options and service requirements. Nominal diameter is one input to that decision.

Is a larger housing automatically more flexible?

Verify which loads and internal arrangements its design supports. Obtain the parts and drawings for each arrangement the site intends to use.

What if the existing module drawing is unavailable?

Provide identification, photographs and the available dimensions, then have the supplier document what remains unresolved before approving the order.

Which documents should be requested before shipment?

Agree on the assembly drawing, itemized parts, applicable material and test records, and operating instructions in the purchase scope.

Request a specification review

Contact LOONGFiltration with the liquid, batch range, processing window and seven specifications. Include the existing equipment information so the proposed housing and modules can be assessed together.

Visit the LOONGFiltration website or browse the official YouTube channel for further company resources.

Table of Content
Leave a comment if you are interested.
Welcome your message, we will reply you within 24 hours. In addition, your email will not be displayed.​​​​​​​
INQUIRY
A SPECIALIST IN FILTRATION EXCELLENCE!

 Tel: +86-571-26232618
 WhatsApp: +8619558243921
 Email:
sales@loongfiltration.com
Address: 19.Building 12, No. 42, Tianhe Road, Donghu Street, Linping, Hangzhou, Zhejiang,P.R. China

COMPANY

PRODUCT

APPLICATION

Copyright 2025 LOONG FILTRATION All Rights Reserved. Sitemap | Privacy Policy