Views: 26 Author: Site Editor Publish Time: 2026-11-18 Origin: Site
Nominal vs absolute filter ratings should be compared through their measured particle-removal performance and test conditions. The words describe a supplier's rating approach; they do not provide a complete acceptance specification. For a CDU cooling loop, the useful information is the efficiency at the relevant particle size, supported by a method that represents the intended duty.
Start with the protected equipment's requirement in the CDU and cold-plate filter selection guide. Once that requirement is defined, the rating review can establish whether an offered element provides the required evidence. Its housing material and model designation need separate consideration.
Request the supplier's definition of nominal or absolute alongside the micron value.
Compare efficiency at the same particle size using compatible test methods.
Check the tested element identity and the conditions covered by the report.
Review hydraulic and material suitability separately from particle retention.
A nominal rating describes a filtration grade using the manufacturer's stated basis. Ask for the quantitative removal performance behind that grade. Two nominal-rated elements carrying the same micron value may have different efficiencies or may have been assessed using different methods.
Absolute is commonly used for a more tightly specified retention claim, but the buyer still needs the supplier's efficiency definition and supporting test. Avoid assigning one removal percentage to every product labelled absolute. Its meaning must remain tied to the stated method and conditions.
Particle-removal efficiency describes the fraction of a defined particle population removed during the test. A beta ratio expresses the relationship between upstream and downstream particle counts at a stated size threshold. Both require the size basis and measurement method to be meaningful.
Datasheet term | What it describes | Information still needed |
|---|---|---|
Micron rating | A particle-size value associated with the grade | Rating definition, efficiency and test method |
Nominal | The manufacturer's stated nominal-grade basis | Quantitative removal performance and applicable conditions |
Absolute | The manufacturer's stated absolute-retention basis | Defined efficiency or retention criterion and relevant results |
Efficiency | Removal of the specified challenge-particle population | Particle-size basis, counting or mass method and operating conditions |
Beta ratio | Upstream/downstream count relationship at a stated threshold | Particle sizing, test procedure and reporting basis |
Mesh opening | A geometrical description of the mesh | Whether a retention claim has also been measured |
Keep these entries separate in a comparison sheet. Converting every term into a single micron column hides the evidence the engineer needs to approve a substitution.
Request the method identifier, revision and any departures from it. Establish the challenge material, test fluid and operating conditions. Results measured by particle count and results expressed by retained mass can describe different aspects of performance; do not treat their percentages as interchangeable.
ISO 16889:2022 describes a multi-pass method for hydraulic-fluid-power filter elements, including particle removal, contaminant capacity and differential-pressure characteristics. Its published scope requires attention to the validated test range. A report referring to this method needs an applicability assessment before it supports a particular coolant filtration requirement.
Ask whether the result is based on a single-pass or recirculating test. Retain the actual method description instead of assuming that a multi-pass test directly reproduces the circuit's operating behavior. The qualification objective and the laboratory procedure should be agreed with the equipment owner.
Review the uncertainty and the reporting convention around the particle size of interest. Where the required size lies outside the demonstrated measurement range, obtain appropriate evidence. Extrapolating a datasheet grade into an untested range creates an acceptance gap.
Record the exact element code, media construction and dimensions covered by the report. Check the support structure and end connection as well as the nominal length. A test on another format needs a documented engineering justification before it supports the offered configuration.
Where a manufacturer supplies several grades within a family, identify the actual grade used in the test. A family brochure may summarize available options without demonstrating the proposed element's performance. Retain the product-specific record with the approved parts list.
Check whether the reported performance covers a new element only or also its condition during a defined loading sequence. Ask how the result is summarized over that sequence. An average result and the lowest demonstrated efficiency answer different acceptance questions, so use the reporting basis specified by the project.
Installation also needs review. The element must fit and seal correctly in its housing. An incorrectly seated seal can allow coolant to pass around the intended filtration path. A retention test on a correctly assembled specimen cannot establish the performance of a misassembled installation.
Obtain the cold plate and other sensitive component requirements in writing. Identify the particle-control objective, relevant size thresholds and any prescribed qualification method. The smallest flow-passage dimension alone does not establish a suitable element rating.
The OCP Reservoir and Pumping Unit Specification, version 1.0, section 9.3 relates filtration requirements to the connected particle-sensitive components. Use the applicable equipment requirements to select the element; do not copy a reference-design rating into every cooling circuit.
Write the required efficiency and evidence into the RFQ. If an existing specification contains only a micron number, ask the equipment owner to clarify its intent before approving alternatives. The clarification should become part of the controlled specification so replacement purchases use the same basis.
Acceptance question | Document to examine | Decision before ordering |
|---|---|---|
What particle control is required? | Protected-equipment specification | Define the relevant size and removal target |
How is the offered grade rated? | Supplier rating definition | Resolve nominal/absolute terminology |
What does the test cover? | Method, specimen identity and conditions | Confirm relevance to the proposed element |
How is performance reported? | Efficiency results and reporting convention | Check compliance against the required criterion |
Will the assembly fit and seal? | Housing and element drawings | Approve the installed configuration |
Can it operate at the required duty? | Hydraulic and compatibility evidence | Complete the separate system suitability review |
A demonstrated retention grade does not establish acceptable pressure drop. Review the clean assembly curve at the required flow and fluid conditions, then retain operating margin for contamination loading. A finer grade may need a different element area or housing configuration to meet the same duty.
Coolant compatibility needs its own review of every wetted material. Provide the commercial formulation and operating range. Where cleaning or reuse is proposed, establish how acceptable retention will be confirmed after that process instead of assuming the original rating remains valid indefinitely.
Particle filtration also has a defined treatment scope. A particle-rating claim cannot establish that dissolved contamination has been removed or that a coolant meets a microbiological requirement. Set those acceptance objectives separately with the equipment and coolant suppliers where they apply.
For a proposed configuration, review the LOONGFiltration liquid-cooling application information and identify the element alongside the CDU-2 Inline Filter housing. Submit the retention requirement and accepted test basis through the LOONGFiltration website. The official YouTube channel provides product viewing material, while rating approval should rely on the relevant technical records.
No. Request the manufacturer's definition and the measured performance supporting the grade. Specify the efficiency or retention criterion required by the project instead of relying on the word absolute alone.
Yes. Their efficiency, test method or element construction may differ. Compare the particle-size basis and relevant test results, then check hydraulic and coolant suitability for the installed assembly.
An opening value describes mesh geometry. Establish whether the supplier also provides a measured retention claim and its method. Use the evidence required by the protected equipment to decide whether the proposed element is acceptable.
Identify the approved element code, rating definition, acceptance criterion, media construction and end connection. Include the compatible seals and any change-control requirement so future purchases reproduce the qualified configuration.