You are here: Home » News » Technology Insight » Full-Flow vs. Side-Stream Filtration for CDU Cooling Systems

Full-Flow vs. Side-Stream Filtration for CDU Cooling Systems

Views: 0     Author: Site Editor     Publish Time: 2026-11-18      Origin: Site

Inquire

facebook sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

Full-flow filtration places the filter in the circulation path so the flow through that defined path passes through the element during normal operation. Side-stream filtration treats a branch of the coolant flow and returns it to the circuit. The choice depends on what requires protection, how quickly particles must be intercepted and how much hydraulic resistance the cooling system can accommodate.

Define those requirements with the CDU and cold-plate filter selection guide before comparing filter sizes. These arrangements can serve different functions within one system. Their suitability depends on the actual circuit and the equipment supplier's requirements.

Key takeaways

  • Full-flow filtration can intercept particles on a defined supply path before they reach downstream equipment.

  • A side-stream branch treats part of the circulating inventory over time.

  • Size each filter against the flow it actually receives and the pressure available to it.

  • Confirm the effect of servicing, branch-flow changes and bypass arrangements on the protected cooling duty.

Start with the contamination path

Mark the particle sources and protected components on the loop schematic. Potential sources include installation debris, corrosion products and contamination introduced during fluid handling or maintenance. Establish where those particles can enter relative to the proposed filter.

If protection requires particles to be intercepted before a particular component, evaluate the full flow path leading to that component. A filter elsewhere in the circuit may improve the circulating fluid condition without providing that immediate barrier. Verify any unfiltered connections, makeup points or bypass paths as part of the review.

Side-stream treatment addresses a defined fraction of the circuit flow on each pass through the branch. Its effect on the circulating inventory depends on branch flow, retention performance, mixing and the rate at which particles enter or are generated. It cannot be assumed to remove every particle before the particle's first passage through a cold plate.

The OCP water-based transfer-fluid guidelines, section 4.4 describe a side-stream arrangement and additional component-protection filtration within their water-based rack context. Apply the relevant system requirements when designing another loop; the reference arrangement does not establish one universal branch-flow percentage or micron rating.

Compare the functions of each arrangement

Choose the topology according to the protection objective and the permitted operating states. A circuit can combine an inline protective element with a separate treatment branch if the equipment owner approves the arrangement and its hydraulic effects.

Design question

Full-flow arrangement

Side-stream arrangement

Which coolant crosses the element?

Flow through the defined filtered circulation path

Flow routed through the treatment branch

Where does particle interception occur?

Before the downstream equipment when correctly positioned on its supply path

During passage through the branch, without an automatic first-pass barrier elsewhere

Which hydraulic duty sizes the filter?

The required flow of the filtered main path

The required branch flow and its driving pressure

What happens as resistance rises?

Main-path flow or pump demand can be affected

Branch treatment flow can change, depending on its controls

What does maintenance require?

An approved interruption or alternative filtered path where needed

Approved branch isolation while maintaining the required main-loop conditions

What needs verification?

Protection coverage and cooling flow in every permitted state

Branch flow, inventory treatment objective and interaction with the main circuit

Parallel housings can still form part of a full-flow design if the circulation path is filtered through the available housings. A duplex changeover design needs its own rated capacity and operating procedure. Describing equipment as parallel or duplex does not establish that the remaining path can carry the required duty during service.

02-compare-full-flow-and-side-stream-1600x1000.png

Check the full-flow pressure budget

The full-flow filter must fit within the available hydraulic budget while the loop delivers its required cooling flow. Include housing and connection losses as well as element resistance. Identify the fluid and temperature conditions behind the pressure-drop data.

Retain margin between the clean condition and the agreed service trigger. As the element loads, the pump or control system may respond differently depending on its operating mode. Assess the relevant operating states with the CDU designer, including the effect on the most demanding flow path.

The OCP Liquid-to-Liquid CDU Test Methodology and Performance Rating discusses TCS pressure head against network losses. For filter selection, that system-level relationship means a low-resistance element must still be checked within the complete circuit.

Do not add an unfiltered bypass as an assumed remedy for a loaded filter. A bypass changes the particle-protection condition and needs explicit equipment-owner approval. Where cooling continuity is required, evaluate a suitably designed alternative path or service arrangement with the associated controls and acceptance requirements.

Establish and verify side-stream flow

Determine the treatment objective before selecting the branch flow. A separate branch may be driven by its own pump or by a pressure difference available in the circuit. Each approach needs a hydraulic assessment for its intended operating range.

Select the branch element and housing for that duty, including the expected resistance during service. A main-loop flow value does not establish the flow through a passive treatment branch. Changes in valve positions, pump speed or filter loading can alter the branch's operating point.

Provide a way to verify that the required treatment flow is present. Differential pressure across an element is useful when interpreted with known flow and fluid conditions, but it does not by itself establish adequate branch throughput. Agree on the instruments and alarm logic with the system designer.

Place the branch takeoff and return so they support the intended inventory treatment. Review the possibility of short-circuiting between them and the influence on main-loop flow distribution. Keep the branch within the same approved coolant circuit; facility and secondary fluids should retain their designed separation.

03-size-each-filter-for-its-duty-1600x1000.png

Plan commissioning and maintenance states

Treat construction cleanup as a separate duty from steady operation. A temporary flushing arrangement may be required before sensitive components are connected. Neither a permanently installed full-flow filter nor an ongoing side-stream branch automatically proves that the loop meets its commissioning cleanliness criteria.

Review how a service action affects particle protection and cooling continuity. For a side-stream branch, isolation should leave the main circuit in its required operating condition. For a full-flow assembly, the approved procedure must explain whether cooling pauses or another qualified path takes over.

After replacement or cleaning, restore the correct flow path and confirm closure, sealing and operating conditions. Record the clean differential pressure at the associated flow and coolant temperature. For a side-stream system, include the restored treatment flow in the record.

Condition to review

Evidence required

Acceptance decision

Normal operation

Main and branch flow data, defined filter configuration

Required cooling and filtration duties are both maintained

Loaded filter

Hydraulic assessment and service limits

A service action occurs before an unacceptable operating state

Filter isolated

Approved flow path and maintenance procedure

Cooling continuity or interruption meets the site's requirement

Commissioning

Flushing plan and cleanliness acceptance records

The loop is ready for the protected equipment

Restart

Leak checks, flow verification and clean baseline

The approved operating arrangement has been restored

Changed load or expansion

Updated circuit assessment

New operating states remain within the qualified duty

04-review-operating-states-1600x1000.png

Specify the topology and components together

Include the schematic with the RFQ. Identify circuit boundaries, flow directions, treatment duty and relevant control states. Ask for the required retention evidence and the complete wetted-material list alongside the pressure-drop data.

The LOONGFiltration liquid-cooling application page covers inline and side-stream filtration contexts. A product such as the CDU-2 Inline Filter still needs an identified element and a duty-specific configuration review. Its housing name does not determine whether a proposed system arrangement provides the required protection.

Submit the loop schematic and operating requirements through the LOONGFiltration website. The official YouTube channel can help with product viewing. Approve the topology using the drawing, hydraulic assessment and equipment requirements for the actual installation.

FAQ

Is side-stream filtration a replacement for full-flow filtration?

It depends on the specified protection duty. A treatment branch does not automatically provide particle interception before every downstream component. Follow the protected-equipment requirements when deciding whether an inline barrier is also needed.

What percentage of main flow should the branch filter treat?

Determine the branch flow from the inventory-treatment objective, contamination conditions, element performance and circuit hydraulics. A percentage used in one reference system cannot establish the correct duty for another installation.

Can a side-stream filter always be serviced without affecting cooling?

Only if the approved design and isolation procedure maintain the required main-loop conditions. Verify branch connections, control responses and the system operating state instead of assuming that branch isolation has no hydraulic effect.

Can both arrangements be used in one CDU cooling system?

Yes, when they serve defined functions and the complete configuration has been reviewed. Establish the role of each filter, its actual flow and the acceptance criteria for normal operation, service and restart.

Table of Content
Leave a comment if you are interested.
Welcome your message, we will reply you within 24 hours. In addition, your email will not be displayed.​​​​​​​
INQUIRY
A SPECIALIST IN FILTRATION EXCELLENCE!

 Tel: +86-571-26232618
 WhatsApp: +8619558243921
 Email:
sales@loongfiltration.com
Address: 19.Building 12, No. 42, Tianhe Road, Donghu Street, Linping, Hangzhou, Zhejiang,P.R. China

COMPANY

PRODUCT

APPLICATION

Copyright 2025 LOONG FILTRATION All Rights Reserved. Sitemap | Privacy Policy