You are here: Home » News » Technology Insight » How to Read a Coolant Filter Pressure-Drop Curve

How to Read a Coolant Filter Pressure-Drop Curve

Views: 0     Author: Site Editor     Publish Time: 2026-11-20      Origin: Site

Inquire

facebook sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

A coolant filter pressure-drop curve shows the pressure loss associated with flow through a defined filter configuration under stated test conditions. To use it for CDU filter selection, identify what was tested, match the fluid conditions to your loop and compare the loss at the required flow with the pressure available for filtration.

A curve for an empty housing, a bare element and an installed assembly can describe three different hydraulic boundaries. Before choosing a size, use the CDU and cold-plate filter selection guide to establish the filtration duty. The curve can then support a documented decision about flow resistance and service margin.

Key takeaways

  • Read the test conditions and configuration identity before reading a duty point.

  • Confirm whether pressure loss covers the element, housing or complete installed flow path.

  • Match coolant formulation, concentration and temperature to the data or obtain a justified correction.

  • Keep clean pressure loss, the maintenance trigger and the element's differential-pressure limit separate.

Identify the curve and its measurement boundary

Start with the part codes, drawing revision and pressure measurement locations. A curve should identify the element grade and size, the housing version and the connections included in the test. Check whether the document describes measured data, a calculated estimate or a supplier's recommended operating envelope.

Pressure taps define the reported loss. Taps across a complete assembly can include internal passages and connection losses as well as the element. A bare-element test may exclude those contributions. Additional site valves or adapters also need a place in the system's hydraulic assessment if the test did not include them.

Request clarification when a graph carries only a product-family name. A line for one element construction does not automatically represent another grade or length. Keep the approved combination attached to the curve so procurement can reproduce it when ordering replacement parts.

Curve information

What to confirm

Consequence of a missing detail

Configuration

Housing code, element code, seals and drawing revision

The tested combination may differ from the offered assembly

Measurement boundary

Pressure tap positions and included connections

Assembly and element losses cannot be compared consistently

Fluid

Commercial coolant, concentration and concentration basis

A water curve may not represent the proposed glycol blend

Temperature

Test temperature and permitted application range

The fluid's resistance to flow may differ in service

Element condition

Clean, conditioned, loaded or cleaned

The curve may describe a different stage of operation

Data status

Measured points, fitted line or engineering estimate

The appropriate confidence and approval route remain unclear

02-curve-identity-and-measurement-boundary-1600x1000.png

Read the axes, units and family of lines

Confirm the flow unit on the horizontal axis and the pressure-loss unit on the vertical axis. Check whether either scale is logarithmic. Similar-looking graphs can use different units and scales, which changes the interpretation of the same apparent position on the page.

Follow the legend carefully when several lines appear together. A family of curves may represent different element grades, lengths, coolant temperatures or housing sizes. Identify which variable changes between lines before comparing them. A curve label such as "water" also needs the test temperature and the stated configuration.

Locate the required system flow on the flow axis and read the corresponding clean pressure drop for the selected configuration. Use the supplier's underlying data when a printed graph is too coarse for the decision. Preserve the units in the selection record and avoid rounding a close result into an apparent acceptance margin.

03-read-required-flow-and-clean-pressure-loss-1600x1000.png

Match the coolant conditions

Use fluid properties for the actual formulation and temperature range. "PG25" alone does not identify every coolant product or explain whether concentration is expressed by mass or volume. Record those details before requesting a corrected curve.

Dow's FLUIDFILE technical resource treats fluid identity, concentration and temperature as inputs to heat-transfer-fluid property comparisons. That supports using condition-specific fluid data. Its pipe and fluid calculations do not, by themselves, qualify a filter assembly or establish a correction for every filter medium.

Ask the filter supplier how any correction was derived and where it applies. A method appropriate for one medium or flow regime may not cover a different element or the connection losses of a complete assembly. Where the conversion is uncertain, request relevant testing instead of extending a simple multiplier beyond its documented range.

Include the conditions that challenge flow delivery, such as the specified startup temperature, as well as normal operation. Confirm which condition governs sizing with the CDU designer.

Compare resistance with the available pressure budget

The usable pressure for filtration comes from the complete circuit assessment. Account for the cold plates, manifolds, connectors, valves and other flow-path losses at the required operating condition. The filter's clean loss then needs to fit within its assigned allowance while leaving an agreed service margin.

The OCP liquid-to-liquid CDU test methodology, Revision 1.0 distinguishes TCS pressure-head performance from facility-side flow impedance. Its system curves concern a CDU and its test boundary. A CDU pump-head graph therefore cannot be used as a filter pressure-drop curve.

Compare the filter result with the available pressure at the same required flow and operating condition. Check the designer's limiting operating modes, including any reduced-capacity mode the installation must support. Changing the filter size or construction is one possible response to an excessive loss, but any change still needs the retention and compatibility review.

Separate clean loss from loading and mechanical limits

A clean pressure-drop curve describes the initial condition stated in the test. It does not predict how quickly the filter will load or establish a calendar replacement interval. That behavior depends on the contamination reaching the filter, its capacity under the duty and the loop's operation.

An element's maximum differential pressure is a separate mechanical limit. The system may lose adequate cooling flow before reaching it. A housing's operating-pressure rating concerns pressure containment and cannot be substituted for either value.

Define the maintenance trigger with the equipment owner and supplier. Record a clean baseline during commissioning, including the flow and coolant temperature. Compare subsequent readings at equivalent conditions or use an approved method to account for changes. A lower pressure loss after an intervention also needs investigation if the element fit, bypass position or instrument condition has changed.

Value or document

What it answers

What it cannot establish alone

Clean assembly curve

Initial pressure loss at defined flow and fluid conditions

Loading rate or service interval

Bare-element curve

Element resistance within its test arrangement

Total installed assembly loss

Element differential-pressure limit

Permitted pressure difference under specified conditions

A suitable maintenance alarm for the full loop

Housing pressure/temperature rating

Permitted pressure-boundary operating envelope

Filtration efficiency or available cooling flow

CDU pressure-head curve

Available pressure for the stated CDU configuration

The pressure loss of an individual filter

Operating trend

Change against a comparable baseline

The cause of the change without further checks

04-pressure-budget-service-and-mechanical-limits-1600x1000.png

What should a supplier submit for approval?

Ask for a curve or data table tied to the quoted housing and element, together with the test conditions and measurement boundary. State the required flow range, actual coolant and the pressure allowance assigned by the CDU designer. Request the element's limits and proposed service criteria separately.

For the LOONGFiltration CDU-2 inline filter, confirm the selected housing version and installed element before accepting hydraulic data. A product designation does not identify every possible cartridge combination.

Submit the duty and available documents through the LOONGFiltration liquid-cooling page or the company website. The official LOONG-filtration YouTube channel provides visual product references; approve hydraulic performance against configuration-specific documents.

FAQ

Does a lower curve always indicate the better filter?

Compare products that meet the same retention and compatibility requirements under equivalent test conditions. A lower clean loss is useful only within that controlled comparison. It cannot establish particle-removal performance or loaded service behavior.

Can I extend a curve beyond its highest tested flow?

Obtain the supplier's engineering approval and supporting basis. Extrapolating beyond the documented range can overlook changes in behavior or configuration limits. Request data covering the operating range needed for the project.

Why does measured pressure drop differ from the datasheet?

Check the element identity and condition, flow measurement, fluid formulation, temperature and pressure tap positions. Also check instruments and included fittings. The difference needs investigation against the same boundary used for the approved curve.

Can the clean curve set the replacement alarm?

It provides a baseline, but the alarm also needs the available system pressure, minimum required flow, element limits and approved maintenance approach. Agree on those conditions before commissioning and record the clean operating point for future comparison.

Table of Content
Leave a comment if you are interested.
Welcome your message, we will reply you within 24 hours. In addition, your email will not be displayed.​​​​​​​
INQUIRY
A SPECIALIST IN FILTRATION EXCELLENCE!

 Tel: +86-571-26232618
 WhatsApp: +8619558243921
 Email:
sales@loongfiltration.com
Address: 19.Building 12, No. 42, Tianhe Road, Donghu Street, Linping, Hangzhou, Zhejiang,P.R. China

COMPANY

PRODUCT

APPLICATION

Copyright 2025 LOONG FILTRATION All Rights Reserved. Sitemap | Privacy Policy