You are here: Home » News » Technology Insight » How to Test CDU Filter Flow and Pressure Drop

How to Test CDU Filter Flow and Pressure Drop

Views: 53     Author: Site Editor     Publish Time: 2026-11-17      Origin: Site

Inquire

facebook sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

A CDU filter flow and pressure-drop test should establish how much pressure the identified assembly consumes at the flow rates and coolant conditions the cooling loop must support. The report needs to connect each measured point to an element, housing, fluid condition and measurement boundary. A flow number without those details is difficult to use in system design.

Before preparing a test, define the required operating envelope with the CDU and cold-plate filter selection guide. The method described here is a planning framework for engineering review. The equipment owner and test laboratory should approve the actual procedure, limits and acceptance criteria for their configuration.

Key takeaways

  • Identify the complete housing, element and seal configuration before testing.

  • Place pressure measurements around a documented section of the flow path.

  • Control coolant composition and temperature throughout each measurement.

  • Report uncertainty, repeatability and the relationship to the cooling-loop pressure budget.

Define the question the test must answer

Write the acceptance question before assembling the rig. A clean hydraulic test may need to show that the complete filter stays within its allocated pressure-drop budget over the required flow range. A separate investigation may compare element sizes or determine the contribution of the housing and connections. These objectives need different test configurations and should have separate results.

The OCP Liquid-to-Liquid CDU Test Methodology and Performance Rating, Revision 1.0 distinguishes component and system performance testing and discusses pressure head, flow impedance and reporting conditions. Its CDU framework provides useful context, while a filter test still needs its own defined specimen and measurement boundary.

Agree on the minimum, normal and maximum operating flow conditions. Include relevant startup conditions and allowable fluid temperatures. State whether the objective covers a new clean element, a conditioned element or an element after a separately controlled loading process. Clean hydraulic results do not establish dirt-holding capacity or service life.

Identify the specimen and the measurement boundary

Record part codes, drawing revisions and serial or batch identifiers. Include the element dimensions, media grade, support arrangement and seal material. For a configurable housing, identify the actual closure and connection version. Photographing the assembled rig can support traceability without substituting for its drawing.

Mark the upstream and downstream pressure taps on the test schematic. A curve measured across the element alone excludes losses that occur through the housing or adapters outside those taps. A complete-assembly result should specify which connections and nearby fittings are included.

Test definition

Information to record

Why it affects interpretation

Assembly identity

Housing, element, seals and drawing revision

Ties the result to the proposed purchase configuration

Flow path

Flow direction, orientation and included fittings

Defines the installed arrangement being assessed

Pressure boundary

Tap positions and connection details

Shows which losses are included in differential pressure

Fluid condition

Product, concentration basis, temperature and preparation

Supports comparison with the intended coolant duty

Specimen condition

New, preconditioned or separately loaded

Separates initial resistance from service-related changes

Acceptance scope

Required flow range and allocated pressure-drop budget

Connects the test to an engineering decision

If an empty-housing baseline is measured, keep it as a separate dataset. Subtracting one curve from another requires compatible test conditions and an uncertainty assessment. Directly measured complete-assembly performance remains useful for checking the installed hydraulic duty.

02-test-specimen-and-measurement-boundary-1600x1000.png

Prepare the fluid and instruments

Use a fluid approved for the rig and specimen, then document how it represents the service coolant. For a glycol mixture, record the commercial product, concentration and whether the concentration is expressed by mass or volume. Water results need an agreed assessment before they support selection for another fluid.

Choose a flow meter and pressure instruments with ranges and accuracy suitable for the expected measurements. A sensor sized for a much larger pressure range can provide inadequate resolution for a low-loss assembly. Check calibration status, zero readings and the influence of installation on the instruments. Keep their identifiers in the report.

Temperature belongs in the measurement record, close enough to the specimen to describe its fluid condition. Where the rig measures differential pressure through separate pressure channels, assess their combined uncertainty. Where a differential-pressure transmitter is used, follow its installation and commissioning requirements.

Prepare a clean rig and use an approved fill and air-removal procedure. Entrained air, unstable temperature or changing fluid composition can make the data difficult to interpret. Confirm steady operation before collecting the measurement set.

Collect a controlled flow sweep

Establish the planned flow points without exceeding the limits of the specimen, rig or instruments. Adjust the test controls according to the approved procedure. At each point, allow flow and fluid temperature to settle, then record the pressure difference with the associated conditions.

Define stability and sampling criteria in the protocol. These should reflect the instrumentation and the engineering decision; a generic dwell time cannot establish that every rig has stabilized. Keep raw time-series data where available so reviewers can distinguish stable readings from transients.

Repeat selected points and consider an increasing and decreasing flow sequence where the procedure permits it. Investigate departures between runs before assigning a single curve. Check for temperature drift, instrument offset, trapped air or a change in the specimen condition. Record the investigation and any excluded data with their reasons.

Use the same pressure-tap boundary and fluid conditions when comparing candidates. A different adapter arrangement can change the measured assembly resistance. If a setup change is necessary, document it and explain which comparisons remain valid.

03-controlled-flow-sweep-1600x1000.png

Evaluate the results against the loop requirement

Plot measured pressure drop against flow with the units, fluid condition and specimen identity visible. Show the actual measurement points and explain any fitted line. Keep extrapolation outside the measured range clearly separate from test evidence.

Compare the clean pressure drop with the agreed filter allocation at the required flow conditions. The system review should retain margin for contamination loading and other changes during service. The element's maximum differential-pressure limit and the housing's allowable operating pressure are separate limits, neither of which defines a suitable normal pressure loss.

A hydraulic test also cannot establish particle-retention efficiency or coolant compatibility by itself. Those qualifications need their own evidence. Where results support a particular temperature or fluid range only, state the approved range in the configuration record.

Build a report that supports acceptance

An acceptance report should let another engineer understand the specimen, repeat the conditions and apply the result to the intended circuit. Include the approved procedure and its deviations with the measurement records.

Report section

Minimum useful content

Review question

Specimen traceability

Part codes, batch or serial data and drawing references

Is this the configuration being purchased?

Test arrangement

Rig schematic, tap locations and included connections

Does the result cover the intended assembly?

Measurement quality

Calibration, instrument ranges, uncertainty and stability criteria

Can the data resolve the acceptance requirement?

Operating conditions

Fluid composition, temperature and measured flow points

Are these conditions relevant to the cooling loop?

Results

Raw records, repeated measurements and labelled curves

Are variations and exclusions explained?

Disposition

Acceptance criteria, limitations and reviewer approval

What has been demonstrated, and what remains open?

For a proposed LOONGFiltration configuration, start with the liquid-cooling application information and identify the actual housing and element to be assessed. The CDU-2 Inline Filter product page provides a product reference; request model-specific documents through the LOONGFiltration website. The official YouTube channel can support product viewing, while the signed test record provides hydraulic evidence.

04-hydraulic-test-evidence-and-acceptance-1600x1000.png

FAQ

Should the test cover the element or the complete filter assembly?

Choose the boundary according to the decision. Complete-assembly testing supports the installed pressure-budget assessment. Element-only testing can help characterize a component, provided the report makes the excluded housing and connection losses clear.

Can water test results be used for a glycol coolant?

They require an engineering assessment of fluid properties and test relevance. Use an agreed correction method or additional testing for the actual formulation and temperature range. Label converted estimates separately from measurements.

Does a clean pressure-drop test prove filter service life?

No. Service life depends on contamination loading, operating conditions and the approved maintenance criteria. A clean test establishes initial hydraulic behavior for the stated specimen and conditions.

What makes two supplier curves comparable?

They need compatible specimen scope, measurement boundaries, fluid conditions and flow ranges. Compare their test methods and uncertainty as well. Similar axes and units alone cannot establish that the curves describe equivalent duties.

Table of Content
Leave a comment if you are interested.
Welcome your message, we will reply you within 24 hours. In addition, your email will not be displayed.​​​​​​​
INQUIRY
A SPECIALIST IN FILTRATION EXCELLENCE!

 Tel: +86-571-26232618
 WhatsApp: +8619558243921
 Email:
sales@loongfiltration.com
Address: 19.Building 12, No. 42, Tianhe Road, Donghu Street, Linping, Hangzhou, Zhejiang,P.R. China

COMPANY

PRODUCT

APPLICATION

Copyright 2025 LOONG FILTRATION All Rights Reserved. Sitemap | Privacy Policy